How to Choose an Overlocker (and When You Need a Coverstitch)
Share
Once you have used an overlocker, the inside of your makes never looks quite the same again. Choosing one is another matter, because the specifications are full of loopers, ratios and thread counts that mean little until you have sat in front of a machine. Here is what each feature actually does, and which of our machines suit which kind of sewist.
If you are still deciding whether you need an overlocker at all, read Sewing Machine vs Overlocker: Do You Need Both? first.
Three thread or four thread?
Most domestic overlockers have two needles and two loopers, and you choose how many to thread for the job in hand.
- Four thread: both needles and both loopers. The second needle adds an extra line of stitching, so this is the strongest option and the one for sewing knit garments together.
- Three thread: one needle and both loopers. Lighter and less bulky, it is ideal for neatening raw edges on woven fabrics. The left needle gives a wider stitch, the right needle a narrower one.
- Two thread: one needle and one looper, usually with a small converter fitted. It gives a soft finish on fine fabrics and is used for flatlock seams.
Three and four thread stitches are the bread and butter of overlocking. Where machines differ is whether two thread stitches are included, so check for that if you sew a lot of fine fabrics.
Rolled hems
A rolled hem is the tiny, tightly wrapped edge you see on scarves, napkins and chiffon blouses. How you switch to it varies, which matters if you use it often:
- A lever or dial. Several of the Juki overlockers and the Janome MyLock models change over with a fingertip control, with no plate or foot to swap.
- Removing the stitch finger. On machines such as the Brother 4234D you slide out a small part called the stitch finger.
Many machines sew a 2mm rolled hem, while the Bernette B44 goes down to 1.5mm for very fine edges.
Differential feed
An overlocker has two sets of feed dogs, one in front of the other. Differential feed runs them at different speeds, and it is the control you will reach for most.
- Set above 1, it eases the fabric in, which stops jersey and other knits stretching into a wavy seam. Turned right up, it gathers fabric on purpose.
- Set below 1, it gently stretches the fabric as it sews, which stops fine wovens and silky fabrics puckering.
Almost every modern overlocker has it, so the real question is how easy it is to adjust. A dial on the outside that you can turn while you sew is much nicer than one tucked away.
Threading, the part everyone worries about
Threading is what puts most people off, and it is where machines differ most. The needles are easy enough; it is the two loopers underneath that cause the head scratching.
Colour coded threading
Each thread path is marked with its own colour, so you follow the line from the cone to the looper or needle. Every first overlocker we recommend below uses colour coding, and most people find it far less daunting than they feared. Many also have a lower looper aid, such as Brother's F.A.S.T. system, which brings the lower looper out where you can reach it.
Lay in tension
With lay in tension, the thread slips down between the tension discs as you follow the path, rather than being fed through an eye. It saves time and helps the thread sit properly in the discs, which is half the battle with a balanced stitch.
Air threading
Further up the range, you put the thread into a port, press a button or lever, and a puff of air carries it right through the looper. There is no path to follow and no order to remember. Some machines, such as the baby lock Acclaim, thread the needles with air too. See them all in our air threading overlockers collection.
To see conventional threading step by step, Steve runs through it in our setting up an overlocker tutorial.
Overlocker, coverstitch, or both in one?
An overlocker cannot sew the double row of stitching on the hem of a shop bought T shirt. That is a cover stitch, and it needs a coverstitch machine. A coverstitch machine has no knife. It sews two or three parallel rows of needle thread on top, with a looper thread underneath, so the hem stretches with the fabric. Most also sew a chain stitch.
A combination machine
Combination machines overlock and coverstitch in one. They save space, and many add stitches that use both at once, such as a chain stitch sewn alongside an overlock seam for extra strength. The catch is converting between overlock and coverstitch, which takes practice, so they suit people who overlock all the seams and then do all the hems, rather than switching back and forth all day.
Two separate machines
Plenty of keen dressmakers prefer two machines. Both stay threaded, so you can overlock a seam, turn round and hem it without converting anything, and you can buy an overlocker now and add a coverstitch later. Look for a free arm for sleeves and cuffs, and check the space to the right of the needle if you make larger garments.
Cutting width and presser foot lift
- Cutting width. The knife trims the fabric a set distance from the needle, and a dial lets you change it: wider for heavier fabrics, narrower for fine ones. Being able to disengage the knife is useful too, for stitching over a fold without cutting it.
- Presser foot lift. The higher the foot rises, the easier it is to get thick layers, fleece or ribbing underneath. A knee lifter raises the foot while both your hands stay on the fabric.
Accessory feet
The standard foot handles nearly everything, but specialist feet open up a lot more:
- Blind stitch foot for near invisible hems, and on many machines for flatlock and pintucks.
- Gathering foot for gathering one layer while sewing it to a flat one.
- Piping foot for making and inserting piping in one pass.
- Elastic or tape foot for feeding elastic evenly into waistbands, cuffs and swimwear.
- Beading or cording foot for guiding cord or beads under the stitch for a decorative edge.
Feet are usually made for a particular brand or model, so check before you buy. Our machine feet range is a good place to start, or ring us and we will tell you what fits.
Overlockers and coverstitch machines we recommend
A first overlocker
Brother 4234D is a dependable first overlocker that sews two, three or four thread stitches. The built in needle threader threads both needles, and the F.A.S.T. system takes care of the lower looper. It comes with a blind stitch foot, and the free arm is handy for cuffs and sleeves.
Janome MyLock 654D is quiet and steady, thanks to its metal base plate and HANENITE vibration suppression. It has colour coded guides with a threading chart inside the front cover, lay in tensions and a quick rolled hem change with no plate to swap, and a gathering attachment comes in the box.
Bernette B44 is Bernette's entry level overlocker, with 15 stitches using two, three or four threads and an open, colour coded thread path with a lower looper threading mechanism. Differential feed runs from 0.6 to 2.0, and a cut offs bin catches the trimmings.
Air threading for an easier life
Juki MO-2000QVP uses a strong puff of air to thread both loopers, while the automatic needle threader does the needles in three steps. The LCD screen shows set up and tension settings for 15 stitches at a glance, and the presser foot lifts to a maximum of 8mm.
baby lock Acclaim threads the loopers and the needles with RevolutionAir at the press of a button, in any order. Automatic Thread Delivery means no tension dials to set, the knife and stitch finger move together so you change the true stitch width, and it sews baby lock's decorative Wave stitch.
Overlock and coverstitch in one
Bernina L890 is Bernina's flagship. It air threads all the loopers in one step, and its colour touchscreen has a guided mode that walks you through each set up. It sews with 2, 3, 4 or 5 threads across overlock, coverstitch and combination stitches, with a free arm and a knee lifter. At 13.4kg, give it a permanent home.
Janome 1200D is a 2, 3, 4 and 5 thread overlocker with cover hem and top cover hem built in. It sets the tensions automatically for each stitch and switches to rolled hem without changing the plate or foot. Converting takes some practice, so it suits sewists already comfortable with an overlocker.
A dedicated coverstitch machine
Brother CV3440 is a straightforward way into coverstitch, sewing triple, wide and narrow cover stitch plus chain stitch. Lifting the presser foot releases all the tensions, there is 155mm of space to the right of the needle, and the free arm makes sleeves and cuffs simple.
Juki MCS 1800 sews 4 thread and 3 thread wide and narrow cover stitch, plus a stretchy chain stitch. The presser foot lifts to 8mm and then 10mm so thick ribbing slides underneath, and a hemming guide comes in the box.
Still not sure?
An overlocker is very much a try before you buy machine, and threading one yourself tells you more than any specification. Many of our overlockers and coverstitch machines are set up in our King's Lynn showroom (see which are on display), so give us a ring before you visit and we will make sure the ones you want to try are out.
You can also try Machine Match for a free personal recommendation, compare up to four machines side by side, or browse our overlockers and coverstitch machines. Or call us on 01553 773362 and we will happily talk it through.